{"id":135,"date":"2012-04-11T01:01:48","date_gmt":"2012-04-11T01:01:48","guid":{"rendered":"http:\/\/www.dognmonkey.com\/ihp307x\/?p=135"},"modified":"2012-04-11T19:07:00","modified_gmt":"2012-04-11T19:07:00","slug":"optimize-config-file-for-portability","status":"publish","type":"post","link":"https:\/\/www.dognmonkey.com\/ihp307x\/optimize-config-file-for-portability.html","title":{"rendered":"Optimize Config File For Portability"},"content":{"rendered":"<p style=\"text-align: center;\"><em>These days, most of the CEMs HP3070 systems are old and some are not well kept up, their pins cards may fail in the middle of the run and our production line may halt for days. I believe in optimizing the config file to use as fewer hybrids cards and power supplies as possible. The fewer hybrid cards concentrated on a module means they can run with many existing systems with module with less hybrid card required. We can ask the CEM to move the bad hybrid cards to the slot we don&#8217;t use and swap the good ones to the one we use, we should have our production line up and running in less than half an hour.<\/em><\/p>\n<p style=\"text-align: center;\"><em>Example of a config file with module 2 not used and always turn on control xt.<br \/>\n<\/em><\/p>\n<blockquote>\n<p style=\"text-align: left;\"><em><\/em>target hp3073 standard<br \/>\nenable software revision b<br \/>\nenable testjet\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0 !Not Apply to 9314 B<br \/>\nenable polarity check\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0 !Not Apply to 9314 B<br \/>\nenable express fixturing<br \/>\nenable paneltest\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0 !Not Apply to 9314 B<br \/>\n!enable throughput multiplier !due to ONLY ONE MODULE Available<br \/>\n!enable connect check<br \/>\n!module 2<br \/>\n!\u00a0\u00a0 cards 1 asru c revision<br \/>\n!\u00a0\u00a0 cards 2 hybrid standard double density<br \/>\n!\u00a0\u00a0 cards 3 hybrid standard double density<br \/>\n!\u00a0\u00a0 cards 4 hybrid standard double density<br \/>\n!\u00a0\u00a0 cards 5 hybrid standard double density<br \/>\n!\u00a0\u00a0 cards 6 control plus<br \/>\n!\u00a0\u00a0 cards 7 hybrid standard double density<br \/>\n!\u00a0\u00a0 cards 8 to 11 hybrid standard double density<br \/>\n!\u00a0\u00a0 supplies hp6624 1 to 4<br \/>\n!end module<\/p>\n<p>module 3<br \/>\ncards 1 asru c revision<br \/>\ncards 2 to 5 hybrid\u00a0 standard<br \/>\ncards 6 control xt<br \/>\ncards 7 to 9 hybrid\u00a0 standard<br \/>\ncards 10 hybrid standard<br \/>\ncards 11 hybrid standard<br \/>\nsupplies hp6624 1 to 4<br \/>\nend module<\/p><\/blockquote>\n<p style=\"text-align: center;\"><em>So we use hybrid standard in case some CEMs has old system with NO double density hybrid cards. These days most of CEMs have Series 2 or 3, they should have all double density hybrid cards, then we can remove cards 2-5 and change standard to double density.<\/em><\/p>\n<blockquote>\n<p style=\"text-align: left;\"><em><\/em>target hp3073 standard<br \/>\nenable software revision b<br \/>\nenable testjet\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0 !Not Apply to 9314 B<br \/>\nenable polarity check\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0 !Not Apply to 9314 B<br \/>\nenable express fixturing<br \/>\nenable paneltest\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0\u00a0 !Not Apply to 9314 B<br \/>\n!enable throughput multiplier !due to ONLY ONE MODULE Available<br \/>\n!enable connect check<br \/>\n!module 2<br \/>\n!\u00a0\u00a0 cards 1 asru c revision<br \/>\n!\u00a0\u00a0 cards 2 hybrid standard double density<br \/>\n!\u00a0\u00a0 cards 3 hybrid standard double density<br \/>\n!\u00a0\u00a0 cards 4 hybrid standard double density<br \/>\n!\u00a0\u00a0 cards 5 hybrid standard double density<br \/>\n!\u00a0\u00a0 cards 6 control plus<br \/>\n!\u00a0\u00a0 cards 7 hybrid standard double density<br \/>\n!\u00a0\u00a0 cards 8 to 11 hybrid standard double density<br \/>\n!\u00a0\u00a0 supplies hp6624 1 to 4<br \/>\n!end module<\/p>\n<p style=\"text-align: left;\">module 3<br \/>\ncards 1 asru c revision<br \/>\n!! \u00a0 cards 2 to 5 hybrid\u00a0 standard<br \/>\ncards 6 control xt<br \/>\ncards 7 to 9 hybrid\u00a0 standard double density<br \/>\ncards 10 hybrid standard double density<br \/>\ncards 11 hybrid standard double density<br \/>\nsupplies hp6624 1 to 4<br \/>\nend module<\/p>\n<\/blockquote>\n<p style=\"text-align: center;\"><em>With this configuration, we only 5 hybrid cards to run our program. <\/em><\/p>\n<p style=\"text-align: center;\"><em>Yes, normally we use 1 standard config file to develop our program, but if we pay a little attention, our programs will run well every where and line down is extremely minimal. This is just my experience, if you see something is not correct or need improvement, please let me know, we all make mistake along the way.<br \/>\n<\/em><\/p>\n<p style=\"text-align: center;\"><em>Cheers,<\/em><\/p>\n<p style=\"text-align: center;\"><em>Louis<\/em><\/p>\n<p style=\"text-align: center;\"><ul class=\"lcp_catlist\" id=\"lcp_instance_0\"><\/ul><\/p>\n","protected":false},"excerpt":{"rendered":"<p>These days, most of the CEMs HP3070 systems are old and some are not well kept up, their pins cards may fail in the middle of the run and our production line may halt for days. I believe in optimizing the config file to use as fewer hybrids cards and power supplies as possible. The <a href=\"https:\/\/www.dognmonkey.com\/ihp307x\/optimize-config-file-for-portability.html\" class=\"more-link\">&#8230;<\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[6],"tags":[20],"class_list":["post-135","post","type-post","status-publish","format-standard","hentry","category-tips-and-tricks","tag-config-file"],"views":1240,"_links":{"self":[{"href":"https:\/\/www.dognmonkey.com\/ihp307x\/wp-json\/wp\/v2\/posts\/135","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.dognmonkey.com\/ihp307x\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.dognmonkey.com\/ihp307x\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.dognmonkey.com\/ihp307x\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.dognmonkey.com\/ihp307x\/wp-json\/wp\/v2\/comments?post=135"}],"version-history":[{"count":6,"href":"https:\/\/www.dognmonkey.com\/ihp307x\/wp-json\/wp\/v2\/posts\/135\/revisions"}],"predecessor-version":[{"id":141,"href":"https:\/\/www.dognmonkey.com\/ihp307x\/wp-json\/wp\/v2\/posts\/135\/revisions\/141"}],"wp:attachment":[{"href":"https:\/\/www.dognmonkey.com\/ihp307x\/wp-json\/wp\/v2\/media?parent=135"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.dognmonkey.com\/ihp307x\/wp-json\/wp\/v2\/categories?post=135"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.dognmonkey.com\/ihp307x\/wp-json\/wp\/v2\/tags?post=135"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}