Install Lion 10.7.3 With USB MyHack 3.1 Lion Installer On Lenovo G770 i5 Sandy Bridge

July 21, 2012 Sleepenabler.kext – put in the extra folder for the lid to close and wake up when opens, wake up from sleep… etc.

sleepenabler.kext

And always use portable drive to install before internal hard drive. For Realtek id 0139 card reader isn’t supported, a USB SD card reader is handy.


May 20, 2012 After installing Lion on Asus P8Z68-V LX board, I realized we can boot from Lion partition with -v -f and we don’t have to use idogboot12 cd (no KP). Now this is the easiest way to load Lion!!!

2012-05-16 After a few tries with MyHack, I think this is the fastest and simplest way to install Lion on Lenovo G770 i5 Sandy Bridge HD3000 Graphics 0116:8086.

Unibeast USB Lion Installer has been the most popular way to install Lion without Snow Leopard if we have a working Mac OS X, the only draw back is that it can only be created with Lion Apps only. MyHack 3.1 will accept InstallESD.dmg (in case we extracted from Lion Apps and accidentally deleted the Lion Apps), which is very useful in this case. One more thing beneficial about this installer is that it has “MyFix” which can solve many problems with the installation and we don’t have to install chameleon after the installation, we can boot straight from the partition Lion installed, if we do it correctly especially with our Lenovo G770 i5 HD3000 laptop. BTW, if this procedure works for you, it will be nice to buy the author a cup of coffee at least.

If we have a snow leopard 10.6.3, we can install it to use as a mac os x system to create this MyHack 3.1 Lion Installer. We will need this snow leopard partition to fix the boot crash 1st time from the lion partition because the Extra folder is not installed to boot if you don’t have snow leopard os .

Prepare an 8GB USB drive for installation

Create MyHackUSBLion drive

Use MyFix to install Extra folder in Lion Partition.

To make this installation full proof and easy to work, after the created USB MyHack installer done, drag the smbios, dsdt.aml and plist from my Lions 10.73 extra folder to this Extra folder. After the installation, it will boot perfectly to the partition, all we need to do is to install the kexts for PS2 keyboard and mouse, ethernet, wifi and VoodooHDA.kext (this one is tricky – remove AppleHDA.kext first, reboot then install it) don’t do it until the end, make sure to remove AppleHDA.kext in the extensions folder, run MyFix.

Plug the MyHackLionInstaller USB drive and USB hard drive to the laptop. Make sure to have usb keyboard and mouse ready. Turn on the computer, hit F12 while booting to get to boot menu and select MyHackLionInstaller USB drive to boot.

boot menu Boot from MyHackInstaller

select disk utility GUID partition

create Lion partition erase

Now we can close the Disk Utility and start with the Lion installation. Make sure to select the correct partition.

select partition to install Installation done

Now, according to MyHack Guide, we should have an option to install our Extra folder to the Lion partition 2 minutes before the installation ends, but there wasn’t, as of now, there is no Extra folder in the root of the new Lion partition, if we boot directly from our Lion USB hard drive, we will have a KP. So, if we have a working Mac OS, boot from there or boot USB Lion partition with idogboot12 to run MyFix to install Extra folder and kexts, THE BEST IS TO BOOT WITH -v -f flags, this will not give KP and boot very nicely.

KP after Lion boot from idogboot12

idogboot12 screen click tab key to select menu

It will boot into the Lion without any problem, start follow the instruction of setting up Lion, we need USB keyboard and USB mouse for detection. The camera should work without any problem.

first LION screen plug usb keyboard and mouse

Lion 10.7

From here, we should have full resolution 1600x900x32 and QE/CI/CL because we have dsdt and device-properties in the Extra of the MyHackLionInstaller. Now, all we need to do is to run MyFix to install our LionExtra folder. Install all the kexts, remove AppleHDA.kext from the Extension folder, we can run the 10.7.3 update now or after the reboot. If run 10.7.3 update now, remove the AppleHDA.kext again before reboot because we’re going to install VoodooHDA.kext for sound, we also need to re-install Wifi kexts, run MyFix again, then reboot. The video below shows how we booted freshly installed MyHack1073 partition with Lion, update to 10.7.3 combo, install all kexts, remove AppleHDA.kext (to install VooodooHDA.kext after reboot), run MyFix to install Our Extra folder with Device-properties and DSDT.aml for HD3000 0116:8086 with brightness slider and artifacts fixed.

After reboot, we should have network wifi and Ethernet working, now we can use Multibeast to install VoodooHDA.kext to get the sound. Before installing VoodooHDA.kext, make sure the AppleHDA.kext is removed from the System/Extensions folder

Update 10.7.3 is a breeze, again, if installed VoodooHDA.kext (2.7.3) (using any multibeast ) must delete the AppleHDA.kext before installing this VoodooHDA.kext. If already installed in 10.7 and worked already, just delete AppleHDA.kext after the 10.7.3 update, re-install Network Kexts, run MyFix and reboot, the laptop will be running 10.7.3 perfectly. Stay away from 10.7.4 until further notice.

Done… Any comments or questions, please post.

Thanks for reading.

17 Comments

  • Hello again,

    I didn’t manage to get any of my network devices working on 10.7.4 so have gone with 10.7.3 and am pleased to say everything works accept for my wireless. I am wondering if you have a different wireless card in the g770 than me, I have the bcm4313?

    Also I have a question about kext placement, are the kexts in my Extra/Extension folder being used or are the kexts in System/Library/Extensions the kexts that are used, I have alos noticed that there is a myhack.kext that seems to contain most of the required system kexts for our laptops, are these being used?

    Another question, do you know if speedstep is working with your dsdt?

    • Hello Darryl,
      If you put the kexts in Extra folder, it will overwrite whatever in the S/L/E folder if existed or nonexisted. Yes, your wifi is broadcom and mine is Athero. Get the ids from the windows, open IO80211xxx.kext (show content), plugin, try to show content of AirportBCM4331.kext, open the info.plist and add the bcm4313 in there to see if it works. Always run myfix after. If it doesn’t then remove the ids from the info.plist, try the other BCM43221.kext. One of these should work with your wifi without any problem, it’s very easy. Why do you need speedstep?

      • Thanks for the pointers, unfortunately I can’t get the wifi to work so bought a usb one which works fine.

        Not sure if I do need speedster to work or not? : )

        Do you mind telling me what the EFI string relates to in your boot.plist?

        Also I think my CPU is a slightly different model but it is an i5, is there a chance that using your dsdt could have an adverse affect on my system. As with the speedstep I’m just trying to ensure that I don’t do any damage to my system hardware whilst running mac on it.

      • The device-properties in boot.plist is to tell the system that our graphics card is HD3000. If your graphics card ids is 0116 product id, you’re fine. If your cpu is different model, but the graphics inside it is the same id #, then yours is the same as mine. The important thing is the ids 0116. Why are you keep talking about the speedstep? Does it make that much difference on performance? Just turn on P and C state and just leave it at that. Your wifi should work if you add the device id correctly. Google for your wifi kext, I’m sure it’s out there somewhere.

Leave a Reply to idog Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.